Release notes

What's new in each release, newest first.

0.17.0

A camera can now fall back to other addresses and follow its vehicle's connection, each vehicle's page shows only its own connections, and the Logbook is one page with your totals.

New

  • The Cockpit says which connection a vehicle is on when it can be heard on more than one, such as "Radio · 46 ms". After falling back it turns amber and says why, such as "Internet · 190 ms. Radio not responding". Point at it to see every connection in order of preference, or press it to open the vehicle's Connections.
  • Set up Wi-Fi preference and a cellular backup under Vehicle internet on the vehicle's page. It shows the gateway's current internet route and lets you choose full video, a camera's low-data stream or telemetry only on cellular, with direct local camera routes kept available.
  • Tune a companion computer's Raspberry Pi cameras from the new Cameras section on the vehicle's page, with presets such as Low latency or your own size, frame rate, sensor mode, bitrate and keyframes. If a camera that always runs does not send pictures again within 20 seconds, the computer puts the old settings back by itself. An optional camera watchdog restarts the cameras when one stops sending pictures.
  • Set up saved Wi-Fi networks and internet health checks from a companion computer's Wi-Fi & internet controls. A Linux companion with NetworkManager saves Wi-Fi credentials, priority and metering without leaving its current network.
  • See each companion computer's clock on the vehicle's page: how far it is from this computer's, such as 8 days 6 h behind, and how it was measured. Check over SSH also says whether network time keeps the computer's clock right. The uxduck companion and uxduck forward --onboard from this version answer the clock request.
  • A preflight is now something you start and finish. Your first tick or New preflight starts one. Press and hold Finish preflight to lock it and keep a full copy in the vehicle's History. Reopen preflight lets you change it and finish it again, as often as you need, and Earlier preflights opens any past one. Launch says how long ago the preflight was finished and whether the vehicle has restarted since. A new Preflight finished check, off until you turn it on, can warn or hold the launch until the preflight is finished. In the CLI, uxduck checklist <vehicle> has new, finish, reopen and runs, and the API has checklist/finish, checklist/reopen and checklist/runs.
  • The Cockpit's Checks tab is now two tabs. Preflight is what you check before take-off or before a rover or boat sets off, and keeps your ticks until you clear them. Launch says "Ready to launch" or what holds Take off, with only what needs attention and its fix beside it. A new check warns once the vehicle is armed while home is more than 50 m from it, and offers Set home here. A vehicle with no steps is offered a starter checklist for its kind.
  • See whether a vehicle has RC input. A new RC receiver telemetry item says Receiving, Signal lost or Not seen, and Setup's Radio row shows it with the channel count and RC RSSI. A new Controller input check warns when the vehicle has no controller input, and in Edit checks you choose whether it asks for RC, the link or either.
  • UXDuck Desktop opens the windows you had open again, each where it was. A camera in its own window comes back on the same camera and view, and a second window comes back on its vehicle. A window you close yourself stays closed.
  • Hide the time and level in Messages with the clock button in its toolbar, so a narrow tab gives its width to the text.
  • PX4 vehicles can calibrate their ESCs in Setup, circle a place with Circle it beside Go to, and switch a VTOL to forward flight and back to hover from the Cockpit outside a mission. Forward flight is refused on the ground.
  • Tuning works on PX4 copters, planes and VTOLs, with Feel, Gains, How it flies and snapshots. The parameters of a PX4 vehicle are described from the vehicle itself, with their units, ranges, choices and which need a restart.
  • PX4 logs (.ulg) replay like other logs, with every logged topic available to chart. The Logbook also finds them on an SD card plugged into this computer.
  • A PX4 simulation can practise. A multicopter has Read the panel, Fly there and Land in the circle, and a VTOL has Read the panel.

Improved

  • Give each camera a preferred address and fallback addresses in Camera settings. The camera keeps one tile and streams from one address at a time. UXDuck switches when pictures stop and returns when the preferred address recovers.
  • A camera with fallback addresses follows its vehicle's connection. When the vehicle moves from the radio to the internet, the camera moves to its internet address straight away and comes back with the vehicle. The picture's ⓘ says which address plays, why, and when it next checks the preferred one.
  • A vehicle's page lists only its own connections, the ones that have heard it and the ones added for it. Add connection there sets one up for that vehicle and shows it as waiting until the vehicle answers. Forget takes a connection off a vehicle that it has not heard since UXDuck started, and removing a connection takes it off every vehicle.
  • A vehicle's connections are one list. Each shows its state and how it is doing, with details underneath. Move a connection up or down to change the order for every vehicle, and the list says which one is in use and why.
  • UDP connections come back sooner after a network interruption. They try again as soon as the computer's network changes, and wait at most 2 seconds between tries.
  • The Logbook opens with your totals: moving time and simulated moving time, this month's, entries, vehicles and time armed. Filter it by operator, and open your own entries from the operator menu with Your logbook. Folders of logs from other apps are now Log folders in Settings. Moving time counts from this version on.
  • Logbook entries and long flights open faster in replay. A 12 hour flight opens in about half the time, moving along its timeline takes a fraction of a second, and UXDuck keeps working while it opens. The Logbook marks the entry that is open in replay.
  • A vehicle's History reads as a timeline. Each line starts with its time and a sign for what it is, and your notes sit in cards.
  • Arrange a vehicle's preflight list your own way. UXDuck's checks are grouped under Setup, Link, Controller, Plan and Cameras, your steps can join a group such as Battery, and groups can be renamed and dragged into order. A rule can also ask for a person's tick once it passes.
  • The Cockpit's Controls subtab is clearer. With no controller sending input, Fly with picks the keyboard. Its keys are drawn as they sit on the keyboard, Neutral is now Centre, and a vehicle is never offered a starting value it would refuse.
  • Reset a controller's setup while it is connected, and delete custom mappings you no longer want. After setting up the sticks, choose whether to customise buttons and switches or finish.
  • An RTSP camera's pictures are dated more accurately. UXDuck measures the camera's clock while it plays, or uses the clock of the companion computer it is Served by, a new camera setting. Stream details say which is in use and open wider.
  • The Camera tab takes a photo of every camera at once and lists photos and videos when all of a vehicle's cameras are on screen. With one camera shown large, All cameras comes first among the small cameras, which sit beside the picture in a wide tab.
  • Show large is in a camera tile's "…" menu, or click the picture. A camera's pencil on its vehicle's page opens all of its settings. The Camera tab says that camera settings stay on each computer.
  • Telemetry opens with three columns, and a tile's ⓘ shows when you point at it, so names fit on one line. A value of several words steps down a size to stay on one line.
  • Altitude above sea level and altitude above terrain are telemetry items. The agent can read and chart them with the altitude above home, and searching for AGL finds the one above terrain.
  • More info popovers have Ask the agent in more places, such as Tuning, launch checks and stream details. The agent finds Start again when asked to put a simulated vehicle back or home, and says a parameter's default is its firmware's.
  • The model picker says a different model costs more on the next message of a chat.
  • A parameter with named choices shows each choice's number, finds a choice by name or number, and takes a custom whole number after asking.
  • PX4 vehicles show what PX4 says about arming in their checks, and arm in a simulation that starts in the air. When PX4 refuses a mode for lack of sticks, the notice says to turn on the keyboard or a controller first, and the Cockpit says what PX4 does when they stop.
  • A PX4 simulation can pause and resume from the Cockpit or with Shift+P, and pauses where it touches the 3D scenery instead of stopping.
  • Setup's Restart row is now Restart autopilot.
  • Take off says when a vehicle is already flying and suggests Land or Return to launch instead.
  • Time in the air keeps counting when a vehicle reports being on the ground for a moment in flight. A landing counts once the vehicle has stayed down for 3 seconds.

Fixed

  • On macOS, UXDuck keeps reaching vehicles and cameras on your local network after it starts in the background. Before, they could go offline a few seconds after UXDuck opened.
  • A browser opens UXDuck within a moment of being allowed, and every window connects faster. UXDuck had kept the parameters of every removed simulation and vehicle and sent them to each window.
  • A gimbal, camera, ADS-B receiver or onboard computer on the same link no longer changes what UXDuck shows for a vehicle, and another vehicle's gimbal or camera no longer appears as a vehicle.
  • A vehicle's round trip is timed from when the reply arrived, so a busy UXDuck no longer adds to it.
  • An RTSP camera at an IPv6 address now connects.
  • Controller driving sticks can no longer also trigger saved Arm, Disarm or mode commands. Queued switch commands are checked against the switch's current position before they are sent.
  • On Linux, a controller you have set up shows all its sticks as soon as it connects, instead of asking to be set up again.
  • A controller remembers which vehicle it was pinned to without changing the Cockpit's selected vehicle, and a disconnected target stays pinned.
  • RC RSSI in the header and Telemetry shows as a percentage, such as 100 % instead of 254.00. The raw reading is still in Add tile as RC RSSI (raw).
  • A long AI chat with many tool calls no longer stops with "The request is too large."
  • A PX4 mode change no longer reads accepted when PX4 refuses it, and shows the reason PX4 gives.
  • PX4 simulations no longer freeze a few minutes in. New simulation offers a new PX4 simulator download with the fix.
  • A Camera tab in Full window leaves room for the window's buttons, and dragging the edge of its small cameras resizes them from their current size again.
  • In a narrow Telemetry tile, a value such as Disarmed is shown smaller on one line instead of split mid-word.
  • In a narrow Messages tab, a repeated message no longer squeezes its text into a thin column.
  • A warning's close button sits in its top-right corner, and a notification's close button shows when you point at it.
  • A mission's running step is highlighted with a rounded row inside the list.
  • The sidebar's Feedback row keeps its shortcut and Draft together at the right.
  • On a vehicle's page, the Model dropdown and the other About values line up.

Before you fly

  • UXDuck's checks no longer stop Arm. A check holds the launch, a take-off or a mission started from the ground, and only when set to "Hold Take off until this passes". A check you had set to block arming now holds the launch. A running setup procedure and a restart due now only warn, so set them to hold if you relied on them. Hold "Take off anyway" to launch past a held check. In the CLI, --arm-anyway is now --anyway, and in the API, command/send is refused with reason preflight only for a launch.
  • A finished preflight never expires. Its ticks keep counting at every launch until you start a new one, so start a new preflight when it no longer describes the vehicle in front of you. While it is finished, nobody can change its checklist, the API and the agent included, until it is reopened.
  • A vehicle stays online only while its flight controller is heard. A gimbal, camera or onboard computer that keeps sending no longer keeps it online. An autopilot that reports a generic vehicle type must use component 1 to appear as a vehicle.
  • On macOS, UXDuck asks once more whether it may find devices on your local network. Choose Allow. Until you do, vehicles and cameras on a radio, Ethernet or Wi-Fi stay offline.
  • Test Wi-Fi and cellular failover on your gateway, and camera recovery, on the ground before relying on them. Switching a camera's address can leave a short video gap and starts a new recording segment. Remove duplicate camera entries before putting their addresses on the camera you keep. Vehicle internet controls are not a data cap.
  • Applying a companion camera's new settings, and every restart by the camera watchdog, pauses every camera on that computer for a few seconds. The watchdog acts whether or not the vehicle is armed, so try new camera settings on the ground.
  • A controller mapping with commands on its driving inputs must be repaired before it can be used. Open its Mapping page and remove the listed commands. Resetting a controller needs a new stick calibration.
  • Check a controller's target vehicle and mapping before pressing Use. Reconnecting a controller or restarting UXDuck never resumes control. On Linux and Windows, two identical controllers share one setup and UXDuck uses only one of them.
  • A vehicle with no controller input shows a Controller input warning, which does not stop arming. A controller in UXDuck counts as RC, so choose "RC only" for the check if your transmitter must be the one.
  • The RC RSSI percentage needs ArduPilot or PX4. With another autopilot it shows a dash, so add RC RSSI (raw) from Add tile.
  • On PX4, releasing the keyboard or a controller while armed counts as losing the sticks. With the PX4 defaults it holds for 5 seconds, then returns home. Land first, or set NAV_RCL_ACT or COM_RCL_EXCEPT to what you want.

0.16.0

Each vehicle now uses the best of its connections in an order you set, and you can make your own telemetry values.

New

  • Set one preference order for your connections. Each vehicle uses its best available route and shows the others, the one in use and how each is doing.
  • Make your own telemetry values. Telemetry › Add tile › New calculated value takes a name, a formula over what the vehicle sends and a unit. Charts, the header and the AI see it too, and it syncs with your operator.
  • PX4 simulations start from New simulation without building anything. UXDuck downloads PX4 for your Mac or Linux computer, and its simulations stay on this computer.
  • Each vehicle remembers the controller mapping you fly it with, synced with your operator profile. The controllers page shows what a controller drives beside that vehicle's mapping, so you can check it on the live sticks before pressing Use.
  • A vehicle can have a 3D model of its own. Choose a glTF file (.glb or .gltf, up to 32 MB) in the Model row on its page, and turn it there if its nose points the wrong way. The 3D map, the vehicle view and Setup draw it at the vehicle's size.
  • Telemetry can show Battery cell average beside Battery per cell, for a vehicle that reports its cells or has a cell count set.

Improved

  • Chart lines run smoothly through every value the vehicle sends instead of as stair-steps. A value sent only when it changes still holds flat until the next one.
  • The Cockpit shows the mapping a controller will use on this vehicle before you press Use, and you can change it there. The row is named for how the vehicle moves: Fly with, Drive with or Steer with.
  • Click Mode in UXDuck Desktop's title bar, or the value on the Telemetry Mode tile, to change the vehicle's mode. Your pinned modes come first, and a mode that is dangerous in flight is still pressed and held.
  • PX4 vehicles get clearer wording. A refused Set home no longer names the wrong firmware, Setup no longer offers parameter descriptions written for another firmware, and Practice and Tuning say they do not support PX4 yet.
  • The AI chat's message box grows as you type and you can drag its top edge to resize it.
  • With support details on, a report says how each connection was doing and which route each vehicle used. It never includes addresses.
  • While a report uploads, Send shows how much has gone.
  • In UXDuck Desktop, ⌘Q (Ctrl+Q on Windows and Linux) quits straight away when nothing is running, and still asks first when quitting would stop something.
  • The simulation notices over the map are compact cards that no longer hide the map.
  • The drawer's Expand button uses the same icon as Full window.

Fixed

  • UDP connections recover their socket and find their destination again after repeated failures, without restarting UXDuck.
  • Go to and Change height on a PX4 vehicle now fly to the height above home you give. Before, PX4 read that height as above sea level, which could fly the vehicle into high ground.
  • PX4 vehicles: a refused arm gives the reason PX4 sends, the EKF and wind tiles fill in, Mission mode counts as flying the mission, and a past flight shows whole-number parameters such as SYS_AUTOSTART with their real values.
  • Parameter files saved by QGroundControl are read correctly when you compare them with a vehicle or save them as a set.
  • The Logbook shows every entry again, loading older ones as you scroll, and Export CSV includes them all. In the API, flight/list reads a page at a time: pass a result's older as before for the next page, or ids to read given flights.
  • A report sent soon after UXDuck started or reconnected is no longer refused as too large.
  • A large report on a slow connection no longer fails after a minute. It gives up only when nothing has gone out for a minute.
  • Claude can finish answering after using a tool instead of stopping with an error.
  • A parameter's default is labelled as the vehicle's firmware default in the Parameters tab and for the AI.
  • A link you add in Fleet is scrolled into view and highlighted. An address another link already uses names that link, and a link that hears no vehicle says so.
  • Telemetry's Add tile search finds items that are already tiles, such as RC RSSI, and items with no value yet.
  • A telemetry value's info keeps its buttons inside it, and the battery values say how UXDuck works them out.
  • On the 3D map, bearing and heading arrows point the right way when the map is tilted or turned.
  • A pinch on the 3D map zooms and keeps following the vehicle, and a touchpad pinch zooms in Orbit too.
  • Hiding every line of one unit in a Chart no longer leaves an empty plot behind.
  • Open Modes on the Controllers page goes back to the Cockpit's Modes.
  • Settings › About again shows why a ready update didn't install last time, and warns when beta updates couldn't be checked.
  • On a Mac, the window buttons sit level with the title bar in the main and video windows at any zoom.

Before you fly

  • When a vehicle moves to another connection, uncertain commands are not sent again and interrupted parameter, mission or file transfers are not resumed. Check the vehicle's state before you retry. Test your redundant connections and the vehicle's failsafes on the ground, including the loss of a shared router or power source.
  • A controller in use now switches to a vehicle's own mapping when it moves to that vehicle. If you fly several vehicles with one controller, check Mapping for each vehicle on the controllers page first.
  • PX4 cannot fly a Go to at a height above terrain, so UXDuck no longer offers one. Choose above home or above sea level instead.
  • Calculated values are lost when an older UXDuck on another computer changes the same operator's settings and syncs.

0.15.0

3D maps stay smooth while they follow a vehicle, start in Chase and keep following when you drag.

Improved

  • 3D maps start in Chase, or in Orbit for airships. Dragging turns the camera round the vehicle and keeps following it. Hold Option or Alt while you drag to pan away.
  • 3D map detail in Settings is Light, Standard or Sharp. UXDuck picks Light or Standard for your computer until you choose.
  • When the Cockpit is too narrow, subtabs that do not fit move into a menu at the end of the row.
  • Controller buttons and switch positions offer only the modes of the vehicle you have selected.
  • The Cockpit terrain status shows the full block count and turns the vehicle terrain layer on or off.
  • Settings › About is tidier, with Check for updates first and release notes beside the update they describe.
  • The assistant finds the right action more often when you ask it to do something, such as arming a vehicle.

Fixed

  • PX4: a take-off or landing step without a position now goes up or comes down where the vehicle will be, instead of flying to 0°, 0°. A plan with nowhere to take off from is refused before it is uploaded.
  • The 3D map keeps its frame rate while it follows a vehicle circling over a city. Computers with 16 GB of memory or more keep more scenery loaded.
  • A 3D map left open renews its map session without losing its view.
  • Map controls keep working when traffic or plugin layers appear or disappear.
  • Starting a simulated vehicle without its simulator installed now says which simulator is missing and how to download it.
  • A simulation that finishes starting no longer closes pages you opened in the meantime.
  • Adding or nudging a log in a replay keeps the replay on screen instead of switching to Live.
  • Reloading UXDuck while you hold a controller keeps you as the same operator.
  • After a height change is accepted, the Cockpit height field stops taking your typing.
  • Add a camera keeps a back arrow above its setup forms, and Escape returns to the previous camera.
  • In the browser, chat offers a feedback draft for you to review and send.
  • Signing a computer out ends the watch links it made and closes everyone watching through them.

Before you fly

  • Watch links made before this release stop working. Make a new watch link and share it again with anyone who should keep watching.

0.14.0

Replays show recorded missions as they changed, and saved flights keep them without needing the original file.

New

  • Replays show recorded missions as they changed, including before takeoff. Saved flights keep that mission and parameter history without needing the original file.
  • Pin telemetry to the timeline in a replay, zoom into a section and choose Armed only playback.
  • Tuning brings gain sliders, snapshots, live response graphs and guided AutoTune together. Follow the tuning steps, compare changes and return to an earlier tune.
  • The Cockpit offers more ways to run a mission, including choosing a starting step, pausing and resuming.
  • Draw offline terrain areas on the map and copy them to a vehicle’s card.
  • Chats follow you across computers and browsers.

Improved

  • Mission uploads show progress and confirm the vehicle’s readback.
  • Edit drawn shapes, copy positions in different formats and keep each map pane’s camera choices.
  • Simulated flights start faster.
  • Camera controls and notifications are clearer.
  • Logbook can delete several entries together while keeping recordings other entries use.

Fixed

  • Imported plans keep their waypoint heights.

Before you fly

  • PX4: a take-off or landing step without a position is uploaded as 0°, 0°, and PX4 flies there. Give every take-off and landing step a position until the next release fixes this.

0.13.0

Plans offer more mission commands, grouped and searchable by name or number. Add your autopilot fork's MAVLink XML in Settings → MAVLink messages to plan with its own commands.

The Cockpit shows a compact readiness summary beside the arming state, with the full checklist in Checks. Controllers and keyboard controls have their own Controls subtab, opened with C. Set home from the map, coordinates or the vehicle's position, and give vehicles without GPS an EKF origin.

Simulations explain terrain preparation and failed starts, and let you try again. Terrain heights are more accurate at higher latitudes and reach simulators faster.

The 2D map adds a Terrain style with shaded relief, contours, streams and trails, and each 3D pane remembers its own camera. Map items replaces Markers: draw lines, areas and circles, add buildings, and name and colour them.

Replay's Parameters follows the flight's time and shows who changed what. On-screen displays can show altitude above home, sea level or terrain.

0.12.0

Simulate a plan across vehicles, speeds and winds, then replay the runs together.

Controllers live in the Cockpit: Fly with offers the controller you pick up, and Use claims it. ExpressLRS 4 Bluetooth radios get their own mapping. Windows radios without a known layout keep channels 4, 5, 7 and 8 as axes; if you bound one as a button, set it up again under Other inputs.

Pages and tabs keep their scroll position, and Replay Details can be resized. Companion computers report temperature, CPU, memory, storage and uptime, and Desktop can check them over SSH.

The assistant recognises incomplete parameter downloads and, in Desktop, can file a problem report for you. Link latency shows approximate one-way time.

0.11.0

Surveys can route round exclusion zones, with a margin, a chosen start and an automatic shortest angle. New simulation shows where it will start and asks you to pick a takeoff spot after searching.

Replay the current flight while recording continues, and delete ended Logbook entries even when their logs are missing.

ArduPilot rover and boat controls now use the vehicle’s throttle calibration to find neutral. The preflight check also detects reverse throttle.

The 3D map has a Light mode, clearer loiter circles and pointers to targets out of view.

Dictate in the command palette and place search, or use Talk to ask a question. Alarms can use your computer's voice offline. Desktop cameras can open in separate windows, and transfers can wait on metered networks.

Watch links use the app's read-only layout, and Your computers is removed. Real vehicles ask you to agree to the current terms before arming.

0.10.0

Click a flight in the Logbook to replay it. Save to account makes a flight available on your other computers and in UXDuck Web.

The sidebar is shorter: Get started is one row showing your progress, and Markers and Your computers appear only when you have them.

AI charts and tabs follow the vehicle you select. The operator menu has Help, with documentation, features, release notes and feedback. The command palette finds controllers, simulations, recording and take-off actions by what you mean, and can hide, sort and group vehicles.

Keyboard controls and controller previews use each vehicle's movement names, and submarines, blimps and reversible inputs start at neutral. Stopped simulations have a menu to start, stop or delete them.

Local cameras can show a mirrored preview, and Linux webcams no longer appear twice. Storage cleanup says what it removed and how much space it freed.

0.9.1

Submarines get a world under the water: follow one below the surface and the 3D map shows the water and seabed. A gripper such as Blue Robotics' Newton can be set up on its page and worked from the Cockpit or a controller. The 3D map can also follow the time of day, with stars at night.

Flying by hand is easier to start. Start flying selects the vehicle it creates, Get started adds Fly it by hand, and the VTOL and plane have their own Practice exercises. Radios can leave a stick unused, freeing its input for switches.

Missions draw their loiters and return-home circles. Flights is now Logbook, and its entries can be renamed. Desktop and Web stay signed in to one account across operators until you sign out.

The AI chat takes files and dictation, handles approvals in the chat and exports conversations. Edit a sent message, queue the next one or steer the current task, and choose reasoning effort per chat. New chats get a short title from the first message.

Vehicle Setup opens Files and, on supported vehicles, Scripting, to edit Lua scripts on the flight controller. Add your autopilot fork's MAVLink messages and parameter descriptions in Settings, and uxduck sim build turns a supported autopilot checkout into a local simulator.

Stopped simulations stay in the sidebar until you delete them, and simulations run on iPhone and iPad. Stats for nerds shows MAVLink round trip, message loss and resource use. The new Features page links to every feature and its docs, and updates no longer fail to reopen UXDuck on Windows.

0.8.0

Replay a flight from Flights: a bar at the foot of the window plays it on both maps and in every tab, at up to 16 times. Any tlog opens the same way, from Mission Planner, QGroundControl or MAVProxy, and so does the autopilot's own .BIN log. Flights flown together replay as one operation, with their camera recordings and any video you add in step, and UXDuck Web replays the flights kept in your account.

Plans and the Mission tab are now one Missions page, and each vehicle has its own colour on the map, in the sidebar and on its mission. The Cockpit has a subtab each for Modes, Guide, Simulation and every plugin. A vehicle's Set up opens its page with its calibrations first, including ESC calibration, and a Restart row when a change needs one. Save a vehicle's parameters as named sets and switch between them.

Settings is easier to find your way around, and you can choose a unit for each kind of value. Traffic has filters and range rings, and the map's Terrain button shows terrain for the vehicle or the mission. Holding Take off arms the vehicle and climbs, and why a vehicle can't arm shows next to Disarmed. Simulations are named Sim 1, Sim 2, and you can run more than two in the browser, in Firefox and Safari too. AI replies show their formatting, and chats no longer stop after ten messages.

On Windows you can install just for you, full screen on a Mac works on external displays, and the desktop app can reload if its window crashes.

0.7.2

See air traffic in the new Airspace tab, from a vehicle's ADS-B receiver, a USB stick, a receiver on your network or adsb.lol, with a warning when an aircraft comes close.

Your display settings, links, plans and saved flights follow you to your other computers, with earlier versions to restore. Put markers on the map, including ones that follow a GPS receiver or your phone.

Ask AI in the browser with an approved account. Flights on this computer add up in a logbook, Go to moves into the Cockpit, and paused simulations stay where they stopped.

0.7.1

See air traffic in the new Airspace tab, from a vehicle's ADS-B receiver, a USB stick, a receiver on your network or adsb.lol, with a warning when an aircraft comes close.

Your display settings, links, plans and saved flights follow you to your other computers, with earlier versions to restore. Put markers on the map, including ones that follow a GPS receiver or your phone.

Ask AI in the browser with an approved account. Flights on this computer add up in a logbook, Go to moves into the Cockpit, and paused simulations stay where they stopped.

0.7.0

See air traffic in the new Airspace tab, from a vehicle's ADS-B receiver, a USB stick, a receiver on your network or adsb.lol, with a warning when an aircraft comes close.

Your display settings, links, plans and saved flights follow you to your other computers, with earlier versions to restore. Put markers on the map, including ones that follow a GPS receiver or your phone.

Ask AI in the browser with an approved account. Flights on this computer add up in a logbook, Go to moves into the Cockpit, and paused simulations stay where they stopped.

0.6.0

Pause and resume simulations with Shift+P, move browser sessions between tabs, and try experimental Blimp waypoint missions.

Use video files as cameras, ask the hosted drone assistant, and send feedback with attachments or voice notes.

Mac updates download inside UXDuck. Mission editing, controller setup, Windows installation and Linux windows work more smoothly.

0.5.0

Switch operators on a shared computer, with fresh sign-in and a profile showing your activity.

Choose a colour theme, and native or borderless full screen on a Mac.

Flight-mode menus stay steady. Registration is separate from sign-in. App updates reopen your windows.

0.4.0

Search for a place or address when choosing where to start a simulation.

Double-click a camera's video to fill the window. Webcams and USB capture adapters can now record sound with the picture.

Controllers recover automatically after a browser stall or reconnection, waiting for fresh input before resuming.

On a Mac, full screen fills the display beside the camera notch. In-app updates replace the complete app.

Tab dividers now have resize grips. Double-click one to share the space equally.

0.3.0

UXDuck Desktop now downloads updates in the background and asks before installing.

Every vehicle has a new, freshly designed 3D model, and you can now fly a simulated jet. Fences show as walls on the 3D map, and V switches between viewpoints on 2D and 3D map tabs.

The keyboard can fly real vehicles too, in any flight mode. Vehicle Control is now called Cockpit.

Right-click a tab to move it to another group or split it, without dragging.

If a controller is still held by another of your windows, Take over in Controllers brings it to this one.

0.2.0

You can now open UXDuck on your phone or tablet. Turn on Settings › Connections › Phones and tablets, scan the QR code, and choose whether each phone can only watch or also fly.

Webcams, USB cameras and analog FPV capture adapters now work from the Camera tab, and keep recording with every UXDuck window closed.

Fly simulations with the keyboard from the Control tab, no gamepad needed

0.1.1

This release adds smoother controller setup and flight data over camera video. UXDuck Desktop can now open in its own window, so you can use it outside the browser.

UXDuck Core is available under Apache 2.0, with links to its source from the app and website.

There's also:

  • Plans: draw missions on the map with fences, rally points and surveys, then upload them to your vehicle
  • New 3D map views (Cockpit, Tail, Below), with a horizon and pitch ladder
  • Maps follow the vehicle on their own, and F fills the window
  • Game controllers in UXDuck Web, which keep flying through a reload
  • Find in page and pairing from the menu bar in UXDuck Desktop
  • MCP loads vehicle tools on demand, so agents use less context

0.1.0

First version of UXDuck, supporting web-based simulation and ground testing. Don't fly yet, but share your feedback.